Numerisk skjuvbox för bergsprickorShow others and affiliations
Responsible organisation
2026 (Swedish)Report (Other academic)Alternative title
Numerical shear box for rock joints (English)
Abstract [sv]
En grundläggande förståelse för bergsprickors skjuvhållfasthet och mekaniska beteende, särskilt i större skalor, saknas delvis idag. För att kunna bestämma skjuvhållfastheten för större sprickor in-situ krävs skjuvförsök i fält, vilket är både kostsamt och tidskrävande. Det finns därför ett behov av en metod som kan uppskatta skjuvhållfastheten in-situ på ett mer rationellt och kostnadseffektivt sätt. En möjlig väg framåt är att använda numerisk modellering där sprickytans geometri baseras på skanning. Syftet med denna studie var att utveckla en numerisk skjuvbox där resultaten från numeriska skjuvförsök valideras med resultat från verkliga försök. Med en numerisk skjuvbox kan kunskapen om bergsprickors mekaniska beteende förbättras och förståelsen avseende möjliga skaleffekter öka. Det långsiktiga målet är att möjliggöra användningen av en numerisk skjuvbox för att bestämma skjuvhållfastheten hos större sprickor in situ, som inte kan undersökas i laboratorieskala. Föreliggande arbete utgör ett första steg mot denna målsättning. Den numeriska skjuvboxen som presenteras i denna rapport användes för att uppskatta den maximala skjuvhållfastheten för ett prov med dimensionerna 60 × 60 mm. De numeriska skjuvförsöken utfördes på tre tvådimensionella profiler längs skjuvriktningen. Medelvärdet av dessa tre profiler validerades mot motsvarande laboratorieförsök. Jämförelsen visar att de numeriska skjuvförsöken på ett övertygande sätt kan återge det mekaniska beteendet hos bergsprickor. De tvådimensionella profilerna underskattar dock antalet kontaktpunkter, vilket resulterar i en något lägre mobiliserad friktionsvinkel jämfört med ett verkligt försök. Flera utvecklingsområden har identifierats för fortsatt utveckling av den numeriska skjuvboxen. En tredimensionell modell av skjuvboxen bedöms nödvändig för att korrekt kunna återge fördelningen av kontaktpunkter och därmed bestämma en mer realistisk skjuvhållfasthet. Vidare bygger den nuvarande skjuvboxen på en styv övre provhalva som hålls horisontell under hela försöket, vilket ytterligare reducerar antalet kontaktpunkter och förstärker den tvådimensionella effekten. Denna begränsning bör hanteras i framtida versioner. Slutligen har de numeriska försöken utförts i small strain mode i PFC, vilket innebär att skjuvhållfastheten vid större deformationer sannolikt inte är helt korrekt återgiven, även om den maximala hållfastheten uppskattas väl. Även denna aspekt bör beaktas vid fortsatt utveckling av den numeriska skjuvboxen.
Abstract [en]
A fundamental understanding of the shear strength and mechanical behavior of rock joints, particularly at larger scales, is still partly lacking. To determine the shear strength of larger rock joints in-situ, field shear tests are required, which are both costly and time-consuming. There is therefore a need for a method that can estimate in-situ shear strength in a more rational and cost-effective way. A possible way forward is the use of numerical modelling, where the fracture geometry is based on scanning. The objective of this study was to develop a numerical shear box in which the results from numerical shear tests are validated against those from real laboratory tests. Using such a numerical shear box can improve the understanding of the mechanical behavior of rock joints and increase knowledge regarding possible scale effects. The long-term aim is to enable the use of a numerical shear box to determine the shear strength of larger joints in-situ, which cannot be investigated in laboratory scale. The present work represents a first step toward this aim. The numerical shear box presented in this report was used to estimate the maximum shear strength of a specimen with dimensions of 60 × 60 mm. The numerical shear tests were performed on three two-dimensional profiles along the shear direction, and the average of these profiles was validated against a corresponding laboratory test. The comparison shows that the numerical shear tests can convincingly reproduce the mechanical behavior of rock joints. However, the two-dimensional profiles underestimate the number of contact points, resulting in a slightly lower mobilized friction angle compared to the laboratory test. Several areas for further development of the numerical shear box were identified. A three-dimensional model is considered necessary to accurately reproduce the distribution of contact points and thus determine a more correct shear strength. Furthermore, the current model employs a rigid upper specimen half that remains horizontally oriented throughout the test, which further reduces the number of contact points and amplifies the two-dimensional effect. This limitation should be addressed in future versions. Finally, the numerical simulations were performed in the small strain mode in PFC, which means that the shear strength at larger deformations is likely not fully captured, although the peak shear strength is well estimated. This aspect should also be considered in future development of the numerical shear box.
Place, publisher, year, edition, pages
Stiftelsen Bergteknisk Forskning , 2026. , p. 34
Series
Trafikverkets forskningsportföljer
Series
BeFo rapport, ISSN 1104-1773 ; 196
Keywords [en]
Numerical direct shear test, PFC, Rock joints, Shear strength
Keywords [sv]
Numeriska direkta skjuvförsök, PFC, bergsprickor, skjuvhållfasthet
National Category
Geotechnical Engineering and Engineering Geology
Research subject
FOI-portföljer, Bygga
Identifiers
URN: urn:nbn:se:trafikverket:diva-22425OAI: oai:DiVA.org:trafikverket-22425DiVA, id: diva2:2107667
Projects
Stiftelsen Bergteknisk Forskning, BeFo
Funder
Swedish Transport Administration, TRV 2016/121902026-10-052026-10-052026-10-05